Zema profila puspiekabe

FAYMONVILLE 6-Achs Multimax Satteltieflader - hydr. gelenkt

You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website.

Excerpts from the equipment. Full specifications available upon request.

GOOSENECK
* Gooseneck in SNT design to optimize load floor length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10°
* For tractors: 6 x 2, 6 x 4, and short 8 x 4
* Detachable steel front wall, approx. 400 mm high
* 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches
* Outer beams of the gooseneck with mounting holes for bolt-on lashing rings
* 2 pairs of screw-in lashing rings included (LC 5,000 daN)
* 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN)
* 1 pair of plug-in aluminum side boards, approx. 400 mm high, anodized
* 1 plug-in aluminum rear board, approx. 400 mm high, anodized
* Approx. 40 mm thick hardwood flooring above gooseneck, checker plate flooring above kingpin
* 3.5 inch kingpin
* Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide
* Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917)
* In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, including bracket for hanging supply lines (Faymonville couplers)
* 2 pairs of stake pockets recessed in the gooseneck, for plug-in stakes approx. 100 x 50 mm

LOAD FLOOR
* Extendable load floor, approx. 11,000 mm long, with rear bevel approx. 500 mm x 10°
* Pneumatic locking with conical locking bolts and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective deck length
* BPW axles and suspension, 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered
* 1st axle with electro-magnetic reverse lock via reverse gear and manual activation
* Axle load capacity: 12,000 kg each
* Air suspension with lift and lower valve
* 235/75 R 17.5 3PMSF twin tires
* Mechanical landing gears with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg
* Continuous and, between axles, interrupted approx. 50 mm thick hardwood floor on load deck (increases coefficient of friction)
* Slotted holes for attachable and repositionable bridging elements: – at the fixed part behind the gooseneck – on the front of the load floor
* 1 sliding intermediate table, approx. 500 mm wide, for the sliding tube with large cross-section, checker plate flooring, front and rear with slotted holes for attachable and repositionable bridging elements
* 1 pair of recessed flat lashing rings in the front fixed part of the load floor (LC 10,000 daN)
* 9 pairs of recessed lashing rings, foldable outward, in the load floor perimeter frame (LC 10,000 daN)
* 1 pair of mechanical rear supports
* Remote steering from front and rear via cable remote control, with axle tracking control, no installation required in the tractor
* 1st axle with automatic lift axle function and start-up assist according to EU Regulation 2021/535
* Under the gooseneck and at the rear cross member, left and right, a 7-pin socket each with holder for warning signs
Bledpfergzv Nex Ag Usk
* Factory-applied sand coating on the perimeter frame of the load floor as well as the checker plates and the transition area between load decks

Sludinājums tika automātiski tulkots. Iespējamas tulkošanas kļūdas.